The float or otherwise the filling mechanism in the toilet flush is responsible for filling with water and controlling it. More specifically, it has the responsibility to stop the water supply when it reaches the desired level. Over time or frequent use may cause some damage and need to change the float in your toilet flush.

Usually, a change is needed when it causes leaks,  when the toilet flush is constantly running water. Leaking from the toilet flush can only cause you problems. In addition to the annoying sound, the consumption and the bill of your water will increase respectively. So it’s good to have a float change in the toilet flush before your bill goes up too much. You do not know how? Read 5 simple steps to change the float in the toilet flush yourself and save your pocket.

If you can not find the source of the problem and you are tired of the sound and the waste of water, all you have to do is turn off the water supply and let one of our specialized plumbers take action!

5 Simple Steps to change my float in the toilet flush myself!

Step 1: Remove the old float

The first step in changing the float in the toilet flush is to turn off the water supply switch and drain all the water inside. Then, using a crab, unscrew and remove the spiral water supply pipe. This is the tube that goes from the filling valve to the float and is located either below or on the side of the basin.

At this point, you will notice that there is a clamp on the bottom surface of the container that is connected to the float. Unscrew it with a pair of pliers so that you can remove the float mechanism from the inside. So now, everything is ready to change the float in your toilet flush.

Step 2: Install the new float

The next step in changing the float in your toilet flush is to install the new one. Install the new float where the water supply and the filling mechanism meet. Then screw in again with the crab, the connecting nut and the spiral pipe, as they were originally. A very important element in this step is to make sure that the new float is the same as the old one.

Step 3: Open the upper float valve and clean the system

A very important step in changing the float in the toilet flush is to completely clean the system from rust or dirt that may be present. First remove the upper valve from the new float and turn on the water supply to clean the system. It would be good to hold a glass over the open valve. The glass will stop the dirty water from rushing out due to the pressure.

Step 4: Close the upper float valve again

After cleaning the system completely, turn off the water supply again and fasten the top of the float that you had removed. Install the rear by turning it a quarter clockwise using the windows at the top. Then make sure it is installed correctly and the valve is closed properly.

Step 5: Adjust the water level

The last step in changing the float in the toilet flush is to adjust the appropriate water level. This will help prevent running more or less water than needed. You can adjust the water level by moving the float clip on the toilet flush , up or down. The ideal water level is in the middle of the tank.

Can’t you change the float on the toilet flush yourself? Was there a problem during the process and in the end the damage was not repaired? Do not worry! Post your work on the platform and get offers from the best plumbers, to change the float in your toilet flush immediately.

Why is my toilet flush running? 

We understand how annoying it is to run your toilet flush for many reasons. The first and foremost is the annoying sound we’ve all heard and that can keep you awake all night. The second is of course related to the additional costs that arise, without expecting it. Such a damage implies higher water consumption but also the need for plumbing.

Is your toilet flush running?

If you want to find the source of the problem yourself, before you call a plumber, follow these simple steps.

Carefully remove the lid of the toilet flush and place it securely. Next, pull out the toilet flush and try to identify the toilet fittings to identify the problem. Do not hesitate to put your hand in the toilet flush , if necessary, because the water is clean.

The first thing you need to understand, before dealing with the reason your toilet flush is running, is how it works.

Learn how it works

First, when you open the lid, you will see inside a small ball, filled with air. The ball floats in the water which is accumulated in the toilet flush . This ball is connected to the mechanism by which the valve opens. When the toilet flush is full of water, the ball, after floating, is at a certain height, keeping the water release valve closed.

Very simply and following the laws of gravity, when you push the lever, that is, you pull the toilet flush, the chain inside the cistern pulls and opens the valve. This releases the accumulated water through a hole and a pipe and is driven by pressure into the basin. Then, two things happen at the same time. Water escapes from the release valve while water enters the toilet flush from the inlet valve.

Keep in mind that the toilet flush empties much faster than it fills. Therefore, there is a point at which it is completely empty, at which point the ball reaches the threshold. Then, through the open inlet valve, the refill pipe refills the overflow pipe with water. Your toilet flush will be refilled with water until the floating ball closes the valve again. You have learned the basics of how it works. Let’s see why your toilet flush can run.

But why is the toilet flush running?

The most common reason your toilet flush can run is related to the chain. Chain length may be the source of your problem. If the chain is short, it may prevent the proper release of the release valve on the hole from which water exits the basin. Thus, the water will constantly flow to the basin. On the other hand, if the chain is too long, it can become entangled and thus prevent the proper operation of the toilet flush again.

A ball, such as the one described above, that has not been placed correctly or has been damaged can also be the cause of your toilet flush running, allowing water to flow continuously from the overflow pipe and end up in the pipe.

The problem may even be in the water release valve itself. This is because over time, the valve loses its elasticity. This way it can stop its smooth operation. If, therefore, it does not adequately cover the release passage, water will continue to flow to the basin.

See more about plumbers:

Published by Marie Sandal

Ex bodybuilder, now working as a freelance content writer.

Leave a comment

Your email address will not be published. Required fields are marked *